Samsung Galaxy A3-A320FL was launched in 2017, January, The phone CPU powered by Octa-core 1.6 GHz Cortex-A53, and it comes with 2 GB RAM and 16 GB ROM, microSD, Samsung Galaxy A3-A320FL comes with the Primary Singel 13MP+ 8MP selfie camera and powered by Non-removable Li-Ion 2350 mAh battery.
Firmware Link Download
How To Install The Flash File Full Guide:-
Step 1. First, make sure that you have downloaded the correct firmware file on your PC.
Step 2. Then install the Samsung USB driver.
Step 3. After that Download Odin PC software (Odin 3.13.1)or any other latest version.
Odin Download link
Samsung USB Drivers(Official Download link)
Step 4. Extract the firmware file. You can use a free software like 7-zip for this. Install 7-zip/Winrar, then right-click on firmware file and under 7-zip, select ‘Extract here’. You should get a file in .tar.md5 format now. (You may get 4 or more files, with AP, BL, CP or CSC etc. written at the beginning of those files.) We will be loading this file into Odin, to be installed on the device (in step 10 below).
Step 5. Extract the Odin file. You should get the Odin .exe file (other files could be hidden, may not visible).
Step 6. Disconnect your Samsung Galaxy A3-A320FL from PC if it is connected.
Step 7. Boot into download mode.
How To Get Your Device Into Download Mode:-
- First power off your device. Wait for 6-7 seconds after screen goes off.
- In the second step hold down Volume Down + Volume Up + Power key for a couple of seconds.
- Press Volume Up to continue to download mode.
Step 8. Double click on Odin .exe file (from step 5) to open the Odin window as shown below. Be careful with Odin, and do just as said to prevent problems.
Step 9. Then Connect your device now using a USB Data cable. Odin should recognize your device. When it recognizes, you will see Added!! message appearing in the Log box in the bottom left, and the first box under ID: COM will also show a no. and turn its background blue.
If you don’t get Added!! the message, you need to install/re-install drivers again and use the original cable that came with the device. Often drivers are the problem.
Case 1: If you got a single .tar/.tar.md5 file, then load this into the AP tab of your Odin software. After that go to the next step.
To load the file, click on AP tab, select the single firmware file starting with AP text, wait for it to load, and then skip to step 11, ignoring the rest of the part of this step.
Case 2: If you got more than one .tar/.tar.md5 file, then you must be having files starting with AP, CSC, Home_CSC, BL, CP, etc. stuff. In this case, choose the files as follows. Select the firmware files as follows.
- Click on the BL tab, and select the file beginning with BL text.
- Click on the AP tab, and select the file beginning with AP text.
- Click on the CP tab, and select the file beginning with CP text.
[Different] Click on the CSC tab, and select the file beginning with HOME_CSC text. If HOME_CSC file isn’t available, then select the file beginning with CSC text.
Load the firmware files(s) on your device. This depends on how many files you got in step 4 above upon extracting the firmware .zip file.
Step 10. Then Click on Options tab, and make sure Re-partition checkbox is NOT selected. Don’t use the PIT tab, ever.
Then Go back to Log tab now, as it will show the progress of the firmware installation when you hit the start button in next step.
Step 11. Verify that everything is okay as mentioned above. When satisfied, click the Start button on Odin now to start flashing the firmware on your device.
Wait till installation is finished, after which your device will reboot automatically. You’ll get PASS(Green Colour) message as shown below upon successful installation from Odin.